| Products > Waterborne > Neptune |
          |
CF - 520 - SATIN Technical Data: SURFACE PREPARATION: Preparation: Sand the floor according to NWFA/ NOFMA specifications. Fill all cracks with Precision Full Trowel Filler or Wood Patch. Seal the floor according to label directions using Precision SmoothSeal Waterbased Finish or Precision Penetrating Seal & Stain in selected colors. All other stains should be tested for compatibility. DO NOT apply NEPTUNE 2-Component Waterbased Finish over the floors sealed with wax, non-drying oils, shellac or stearated sealers. It is not necessary and it is not recommended to use SmoothSeal or other sealers on stained floors. TIPS: MIXING: SHAKE WELL BEFORE USING. Shake NEPTUNE finish (Part A) well for 15 to 30 seconds before adding hardener. Pour the finish into a clean, dry plastic container. If less than a gallon is desired, use the graduated marks on the side of Part B container. While stirring vigorously, slowly add one bottle of Neptune Hardener (NH 30 Part B) per gallon of NEPTUNE 2-Component Waterbased Finish (Part A). Continue to stir for 2 to 3 minutes. Let stand for 5 to 10 minutes before applying. NOTE: Use only Neptune Hardener. Never add extra amounts of hardener. DO NOT ADD WATER TO HARDENER. Material with hardener added should not be used after 5 hours. USE CAUTION: Hardener may cause skin irritation. Always wear protective gloves and clothing when handling Hardener. APPLICATION TOOLS: NEPTUNE 2-Component Waterbased Finish can be applied with a nylon bristle brush (for cutting in), synthetic applicator, paint pad, or a T-bar applicator at the spread rate of 400 to 450 square feet per gallon. T-BAR APPLICATION: Apply at the rate of 400 to 450 square feet per gallon.
Pour a 5 to 6 inch bead of material the length of the floor. Cut
in the side with a paint
pad. Pull the finish in a snow plow method from end-to-end in the
room. Always work with the grain of the wood. Swivel the applicator
when 6 inches from the
baseboard and stop in line with the finish bead or puddle. Rock the
applicator to remove excess product and feather the turn mark. It
is important to feather out all
turn and stop marks. Coat the edges at the end of the room just before
the coating of the body of the floor. Touch up ends as you coat across
the floor to feather out
applicator stop marks. Add product to bead in body to maintain a
uniform product bead. By changing the angle of the applicator head,
the product can be repositioned
to maintain a wet edge without pouring out excess material. The speed
of walking during the application and the weight of the applicator
can and will affect
the thickness of material left on the floor. Continue the procedure
across the floor and reduce the size of the bead as you near the
exit from the room. Allow to dry at
least 3 to 4 hours* or overnight before applying the next coat. When
dry, abrade with a maroon abrasive pad. Be sure to hand abrade all
areas not reached with
machine. Vacuum floor and surrounding areas thoroughly and tack with
a lint-free cotton cloth dampened with water. Apply next coat of
NEPTUNE as previously
instructed. DO NOT APPLY MORE THAN 2 COATS THE SAME DAY (Smooth Seal
and/or finish). Always abrade between coats. For floors that the
grain has been
opened before applying stain, you may need an additional coat of
finish. CURING: Wait 24 hours before allowing light traffic on the final coat. The total curing process takes approximately 7 to 10 days. DO NOT place rugs on the floor for approximately 2 to 3 weeks. MAINTENANCE: Maintain floor with routine vacuuming and Precision Wood / Laminate Floor Spray Cleaner according to directions. DO NOT use cleaner for two weeks after final coat. Use felt floor protectors under all furniture. Put walk-off mats at all entrances to keep out excessive dirt. PACKAGING: Gallon 3/Case (Includes (3) 12.8 oz. of hardener) TECHNICAL DATA
|
