|
 |
• Two-component, acid-cured
• For use in high-traffic residential
and commercial areas
• Two hour dry time
• Available in Matte, Semi Gloss, and
Gloss
MSDS |
SF-720 - SUPER MATTE
SF-735 - MATTE
SF-750 - SEMI GLOSS
SF-790 - GLOSS
Technical Data:
USES: Precision Swedish Finish For Pros is a two-component, alcohol-based finish
designed for use in high traffic residential and commercial areas.
Precision Swedish Finish For Pros is simple to apply and dries quickly ( 2
to 3 hours). In most applications only two coats are required; therefore, your
floor-finishing job can be easily completed in one day. Precision Swedish Finish
For Pros is available in Matte, Semi-Gloss, and Gloss levels.
Prior to applying Precision Swedish Finish For Pros, turn off all ignition
sources including pilot lights, heaters, fans, and electrical equipment.
Ventilate
work and adjacent areas to prevent vapor build up. Vapors may travel and
collect in confined and low areas such as basements. Use only in well ventilated
areas. Always wear a NIOSH/MSHA respirator approved for use with organic
solvent vapors. DO NOT EAT, DRINK, OR SMOKE during application. DO
NOT store in unlabeled bottles or other containers.
TIPS:
Allow finish to dry for at least 2 hours between coats.
DO NOT apply below 60ºF or above 90ºF
Test product on unfamiliar species of wood before use.
Keep containers closed when not in use.
Never vary the amount of Super Hardener added.
DO NOT use mineral spirits, paint thinner or commercially prepared
tack cloth.
MIXING WITH HARDENER: Shake container well before adding Precision
Super Hardener to disperse additives evenly. Inspect bottom of
container to ensure
that all additives are dispersed. Pour into an appropriate clean
plastic application container. Slowly add Precision Super Hardener
from the graduated
hardener
container while stirring Precision Swedish Finish For Pros. If the correct
amount of Precision Super Hardener is not added, the Precision Swedish
Finish
For Pros will not cure. Stir in hardener for 60 seconds. Allow to stand
5 to 10 minutes before applying. Stir occasionally during application.
Mix
enough
product
for only one coat. Mixed product may not be usable the next day.
APPLICATION AND COVERAGE: Precision Swedish Finish For Pros may be applied
using a natural bristle brush, lambs wool applicator, short nap mohair
roller, or T-bar applicator. Apply at the rate of 300 to 400 square
feet per gallon with brush or lambs wool and at a rate of 450 to
550 square feet with the roller
or T-bar applicator. For best results, the product and the room temperature
should be between 60ºF to 80ºF during application and drying.
Apply Precision
Swedish Finish For Pros from wall to wall following the grain of
the wood being careful not to overwork the product always keeping
a wet edge. When dry,
screen with a used 100 grit or finer screen. Hand sand all areas
not reached by machine. Vacuum floor thoroughly and tack with a cloth
dampened with
denatured alcohol, lacquer thinner, or water. Provide adequate ventilation
during the tacking process. Apply second coat in the same manner
as the first coat.
Additional coats may be applied for more protection. Do not apply
more than two coats the same day. Only recoat floors that have been
previously coated
with Precision Swedish Finish For Pros. Can be applied over Precision
Penetrating Seal & Stains. All other stains should be tested for compatibility.
DRYING TIME AND RECOAT APPLICATION: Allow finish to dry at least 2 hours.
Temperature and humidity may slow down drying process.
CLEAN UP: Clean tools and applicator with lacquer thinner.
MAINTENANCE: Clean floors regularly by vacuuming to remove grit. Clean
as needed with Precision Wood / Laminate Floor Cleaner. DO NOT use
cleaning products or water within two weeks of final coat.
PACKAGING:
Quart 12/Cases, includes 12 - 1.6 oz net Precision Super Hardener
Gallon 4/Case, includes 4 - 6.25 oz net Precision Super Hardener
2.5 Gallon 2/Case, includes 2 - 15.625 oz net Precision Super Hardener
TECHNICAL DATA
INGREDIENTS: Contains: Petroleum distillates, alcohols, glycol ethers,
and alkyd/urea formaldehyde resin. DENSITY: 7.8 lb/gL SPECIFIC GRAVITY:
.935
VOC with HARDENER: 4.544 lb/gl (545 gm/l) BOILING POINT: 165ºF SOLIDS:
42% VAPOR DENSITY: Heavier than Air
FLASH POINT: 53ºF (38ºC) PERCENT VOLATILE BY WEIGHT: Approximately
58% FLAMMABILITY CLASSIFICATION: Flammable liquid and vapor
STORAGE: Avoid heat and open flames, poor ventilation, corrosives.
Store between 50ºF and 90ºF FREEZE /THAW: Stable
|
